Make taller rounded v4 with IMU mount the sole mechanical design
This commit is contained in:
parent
08241df6bb
commit
8008197c14
@ -1,44 +1,26 @@
|
||||
# 100×80 mm大底板+IMU安装位
|
||||
# 加高圆角 v4+QMI8658C 安装位
|
||||
|
||||
**本目录只保留这一版。** X5、电源外置;双轴上部机构保持原结构,IMU通过可拆边槽座固定在底板左侧。没有v3一体化结构,也没有v4加高8 mm的活动框。
|
||||
仓库当前机械版本。下层活动框加高 **8 mm** 并加圆角,底板保留 **100 × 80 × 5 mm**,左侧新增可拆 IMU 固定座。
|
||||
|
||||

|
||||

|
||||
|
||||
[完整装配STEP](assembly.step) · [打印STL](print/) · [IMU位置与坐标](imu_placement.png) · [源模型与安装说明](selfrising_sg90_large_plate_imu_20261111/README.md)
|
||||
[装配 STEP](assembly.step) · [打印 STL](print/) · [IMU 孔位图](imu_placement.png) · [尺寸来源与生成说明](v4_taller_rounded_imu/README.md)
|
||||
|
||||
## 打印件
|
||||
|
||||
共11件塑料件。下列数量和文件只对应本版:
|
||||
|
||||
| 文件 | 数量 | 作用 |
|
||||
| 打印件 | 数量 | 本次打印 |
|
||||
|---|---:|---|
|
||||
| `large_plate.stl` | 1 | 100×80×5 mm底板,包含IMU固定孔 |
|
||||
| `sg90_mount.stl` | 1 | 下舵机固定座 |
|
||||
| `roll_frame.stl` | 1 | 下活动框与上舵机座 |
|
||||
| `pitch_arm.stl` | 1 | 上活动臂与起身杆 |
|
||||
| `horn_strip_1.stl`至`horn_strip_4.stl` | 4 | 两级舵盘夹条 |
|
||||
| `idler_bushing1.stl`、`idler_bushing2.stl` | 2 | 两级非驱动端衬套 |
|
||||
| `imu_holder_TRIAL.stl` | 1 | 待实物适配的可拆IMU边槽座 |
|
||||
| [底板](print/large_plate.stl) | 1 | 是 |
|
||||
| [下舵机固定座](print/sg90_mount.stl) | 1 | 是 |
|
||||
| [加高圆角下活动框](print/roll_frame.stl) | 1 | 是 |
|
||||
| [QMI8658C 边槽固定座](print/imu_holder_TRIAL.stl) | 1 | 是 |
|
||||
| [上活动臂及一体起身杆](print/pitch_arm.stl) | 1 | 已排除,STL 供完整装配使用 |
|
||||
|
||||
STL单位毫米,已平移至打印坐标原点;摆放方向、支撑和工艺仍需切片确认。[打印文件身份](print_manifest.json)记录每件来源与SHA-256。装配中的蓝色舵机、模块占位及金属紧固件不是打印件。
|
||||
底板新增 **2 × Ø2.4 mm** 通孔用于 M2,孔中心距 **18 mm**,底面有螺母槽。边槽座参考 **21 × 16.4 mm** 的八针模块,板厚暂按 **1.6 mm**。依据与公差见[尺寸记录](v4_taller_rounded_imu/MODULE_DIMENSIONS.json)。
|
||||
|
||||
## 配件清单
|
||||
|
||||
- 双SG90及配套原装舵盘、中心锁紧螺钉;控制程序按360°连续旋转型工作,购买与实物型号需核对。
|
||||
- QMI8658C模块1块、外置RDK X5、电源及连接线。
|
||||
- 本版底座使用四处连接;IMU座另有两处M2×8连接,配螺母和平垫。
|
||||
- 舵机安装耳、舵盘夹条与惰轴的紧固件按本版STEP和实物核对;此前v3/v4的“两颗底座螺丝、四颗自攻螺丝”清单不适用于本版。
|
||||
- 两只 SG90、各自舵盘与中心锁紧螺钉。参考舵盘约 35 mm 长,端孔距 25 mm;共用四颗 1.4 × 4 mm 盘头自攻螺丝直连机构。
|
||||
- 两颗 M2 × 16 mm 螺钉及对应平垫、螺母,固定下舵机座的对角孔。
|
||||
- 两颗 M2.5 × 8 mm 螺钉、两颗 M2.5 螺母和两片 3.2 × 9 × 0.8 mm 加大垫片,用于两级惰轴。
|
||||
- 两颗 M2 × 8 mm 螺钉、两颗 M2 螺母和两片 0.5 mm 厚 M2 平垫,用于 IMU 固定座。
|
||||
|
||||
[接线说明](../RDK/WIRING.md)。IMU模块外形、芯片位置、排针和元件区仍含占位假设,不能仅凭PCB外观认定适配。
|
||||
|
||||
## 修改与生成
|
||||
|
||||
```sh
|
||||
python -B 3Dmodel/selfrising_sg90_large_plate_imu_20261111/build_imu_mount.py
|
||||
```
|
||||
|
||||
脚本使用本版自身的冻结装配`source/assembly.step`,公共原语与渲染工具在`support/`。不再导入其他版本;没有保留它们的模型或生成入口。生成会更新output,请在实验副本中操作,重新核对后同步顶层assembly和print副本。
|
||||
|
||||
本次删除的是仓库当前树中的其他设计,历史提交仍可追溯;原工作区不受影响。
|
||||
|
||||
本版保留25个离散姿态的IMU干涉检查,不等于连续行程、实际装配、带载强度或真机起身验证。本次未重新切片或发送打印。
|
||||
[打印清单](print_manifest.json)记录 STL 哈希与本次排除项。[CAD 检查](v4_taller_rounded_imu/output/verification.json)确认五个网格闭合及 35 个抽样姿态下的 IMU 布置。连续运动、零件强度、实物试装和模块板厚仍需验证。
|
||||
|
||||
Binary file not shown.
|
Before Width: | Height: | Size: 120 KiB After Width: | Height: | Size: 123 KiB |
185167
3Dmodel/assembly.step
185167
3Dmodel/assembly.step
File diff suppressed because it is too large
Load Diff
Binary file not shown.
|
Before Width: | Height: | Size: 135 KiB After Width: | Height: | Size: 134 KiB |
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
@ -1,237 +1,50 @@
|
||||
{
|
||||
"design": "100x80_large_plate_with_imu_only",
|
||||
"physical_printed_parts": 11,
|
||||
"design": "v4_taller_rounded_with_imu",
|
||||
"physical_printed_parts": 5,
|
||||
"requested_print_part_count": 4,
|
||||
"parts": [
|
||||
{
|
||||
"file": "print/horn_strip_1.stl",
|
||||
"quantity": 1,
|
||||
"sha256": "8c29b913911fff1e9acb0bfd74bca824edacaed4091ffd6cc42eebbd99e97e7b",
|
||||
"bounds_mm": [
|
||||
[
|
||||
-1.7763568394002505e-15,
|
||||
0.0,
|
||||
0.0
|
||||
],
|
||||
[
|
||||
2.0,
|
||||
5.0,
|
||||
22.0
|
||||
]
|
||||
],
|
||||
"volume_mm3": 204.80099228659947,
|
||||
"watertight": true,
|
||||
"winding_consistent": true
|
||||
},
|
||||
{
|
||||
"file": "print/horn_strip_2.stl",
|
||||
"quantity": 1,
|
||||
"sha256": "8c29b913911fff1e9acb0bfd74bca824edacaed4091ffd6cc42eebbd99e97e7b",
|
||||
"bounds_mm": [
|
||||
[
|
||||
-1.7763568394002505e-15,
|
||||
0.0,
|
||||
0.0
|
||||
],
|
||||
[
|
||||
2.0,
|
||||
5.0,
|
||||
22.0
|
||||
]
|
||||
],
|
||||
"volume_mm3": 204.80099228659947,
|
||||
"watertight": true,
|
||||
"winding_consistent": true
|
||||
},
|
||||
{
|
||||
"file": "print/horn_strip_3.stl",
|
||||
"quantity": 1,
|
||||
"sha256": "0544d3d4c11be2821dc259d9558d85c879f3925700c9e8319c5d4d5154b48acb",
|
||||
"bounds_mm": [
|
||||
[
|
||||
0.0,
|
||||
-8.881784197001252e-16,
|
||||
0.0
|
||||
],
|
||||
[
|
||||
22.0,
|
||||
2.0,
|
||||
5.0
|
||||
]
|
||||
],
|
||||
"volume_mm3": 204.80099228659947,
|
||||
"watertight": true,
|
||||
"winding_consistent": true
|
||||
},
|
||||
{
|
||||
"file": "print/horn_strip_4.stl",
|
||||
"quantity": 1,
|
||||
"sha256": "52f75a7f507dc0ed07c80658f8dab3ee6f4dac8e161ff941732e9189471c304d",
|
||||
"bounds_mm": [
|
||||
[
|
||||
0.0,
|
||||
-8.881784197001252e-16,
|
||||
0.0
|
||||
],
|
||||
[
|
||||
22.0,
|
||||
2.0,
|
||||
5.0
|
||||
]
|
||||
],
|
||||
"volume_mm3": 204.80099228659947,
|
||||
"watertight": true,
|
||||
"winding_consistent": true
|
||||
},
|
||||
{
|
||||
"file": "print/idler_bushing1.stl",
|
||||
"quantity": 1,
|
||||
"sha256": "8758849f874e3f3e9fade4aeb59c00fff0ac7bf7b17af3be6414e85f654a2cee",
|
||||
"bounds_mm": [
|
||||
[
|
||||
-6.661338147750939e-16,
|
||||
0.0013986809644848108,
|
||||
0.0
|
||||
],
|
||||
[
|
||||
5.0,
|
||||
8.998600959777832,
|
||||
9.0
|
||||
]
|
||||
],
|
||||
"volume_mm3": 145.86650614663665,
|
||||
"watertight": true,
|
||||
"winding_consistent": true
|
||||
},
|
||||
{
|
||||
"file": "print/idler_bushing2.stl",
|
||||
"quantity": 1,
|
||||
"sha256": "1191c6f8ec21d6b4dbb33d9bac4e21587432a9f3ba12a56f2e3b64e21858fd33",
|
||||
"bounds_mm": [
|
||||
[
|
||||
0.0,
|
||||
-6.659267681590495e-16,
|
||||
0.0013986809644848108
|
||||
],
|
||||
[
|
||||
9.0,
|
||||
5.0,
|
||||
8.998600959777832
|
||||
]
|
||||
],
|
||||
"volume_mm3": 145.86650614663665,
|
||||
"watertight": true,
|
||||
"winding_consistent": true
|
||||
},
|
||||
{
|
||||
"file": "print/imu_holder_TRIAL.stl",
|
||||
"quantity": 1,
|
||||
"sha256": "c54d78dc17ece6581342aff5c08768022c747b049333b48a217f67799d81233c",
|
||||
"bounds_mm": [
|
||||
[
|
||||
0.0,
|
||||
0.0,
|
||||
0.0
|
||||
],
|
||||
[
|
||||
24.399999618530273,
|
||||
24.5,
|
||||
3.6500000953674316
|
||||
]
|
||||
],
|
||||
"volume_mm3": 1071.704137498704,
|
||||
"sha256": "6d4d736c9671eeba42d1d7a995eb4daefaa14dca9302035092e2353d65f1f662",
|
||||
"volume_mm3": 1002.8679031565625,
|
||||
"watertight": true,
|
||||
"winding_consistent": true
|
||||
"included_in_requested_print": true
|
||||
},
|
||||
{
|
||||
"file": "print/large_plate.stl",
|
||||
"quantity": 1,
|
||||
"sha256": "cea4104aa9dc7e79e8ae84cd5e52ed88bc183809abdced78d10e7ee940342703",
|
||||
"bounds_mm": [
|
||||
[
|
||||
0.0,
|
||||
0.0,
|
||||
0.0
|
||||
],
|
||||
[
|
||||
100.0,
|
||||
80.0,
|
||||
5.0
|
||||
]
|
||||
],
|
||||
"sha256": "ba3fcbed48fd0f90696dfcf1e5d13009ccffd6f3ba9db2c4e71b3921425f6965",
|
||||
"volume_mm3": 39636.993045700474,
|
||||
"watertight": true,
|
||||
"winding_consistent": true
|
||||
"included_in_requested_print": true
|
||||
},
|
||||
{
|
||||
"file": "print/pitch_arm.stl",
|
||||
"quantity": 1,
|
||||
"sha256": "019412dc6baee788790154fa98a316f47737b1e1227f67b1437ec8c71b0e5f37",
|
||||
"bounds_mm": [
|
||||
[
|
||||
0.0,
|
||||
-8.881784197001252e-16,
|
||||
0.0
|
||||
],
|
||||
[
|
||||
28.0,
|
||||
46.0,
|
||||
109.5999984741211
|
||||
]
|
||||
],
|
||||
"volume_mm3": 13777.599158769444,
|
||||
"sha256": "daf8140f0b13ebc92eb34b5bd455311f5ac90a12c956d6bd11c1b195153242a9",
|
||||
"volume_mm3": 14152.722886220565,
|
||||
"watertight": true,
|
||||
"winding_consistent": true
|
||||
"included_in_requested_print": false
|
||||
},
|
||||
{
|
||||
"file": "print/roll_frame.stl",
|
||||
"quantity": 1,
|
||||
"sha256": "e15fbe860d807cff238499cdd4fcc3e4ad4cba8ffd38d67cd1d542e13ba13765",
|
||||
"bounds_mm": [
|
||||
[
|
||||
0.0,
|
||||
0.0,
|
||||
0.0
|
||||
],
|
||||
[
|
||||
44.0,
|
||||
36.0,
|
||||
73.4000015258789
|
||||
]
|
||||
],
|
||||
"volume_mm3": 10036.786044812932,
|
||||
"sha256": "f65067657f7bed6487978a3c50b1b7818fc45f5f2b624179e0e5e0227680ab8c",
|
||||
"volume_mm3": 11301.16620006733,
|
||||
"watertight": true,
|
||||
"winding_consistent": true
|
||||
"included_in_requested_print": true
|
||||
},
|
||||
{
|
||||
"file": "print/sg90_mount.stl",
|
||||
"quantity": 1,
|
||||
"sha256": "30e48cced427825f61a5fdcdd4584273114f0aa1f6b68c463863ceccfc8fd682",
|
||||
"bounds_mm": [
|
||||
[
|
||||
0.0,
|
||||
0.0,
|
||||
0.0
|
||||
],
|
||||
[
|
||||
34.0,
|
||||
45.0,
|
||||
31.299999237060547
|
||||
]
|
||||
],
|
||||
"volume_mm3": 13442.721198254343,
|
||||
"sha256": "372ac1b1711ab4fb6676c197f02f9cce0760e727db9900669602e72aef991709",
|
||||
"volume_mm3": 24504.892151020627,
|
||||
"watertight": true,
|
||||
"winding_consistent": true
|
||||
"included_in_requested_print": true
|
||||
}
|
||||
],
|
||||
"source_assembly_sha256": "6f35e9692ad1a41262153bf390a2bb10394a6b1940817cc7ff6ac218288e36f2",
|
||||
"reconstruction": {
|
||||
"assembly_labels_match": true,
|
||||
"maximum_part_volume_difference_mm3": 2.9103830456733704e-11,
|
||||
"bounding_boxes_match": true,
|
||||
"discrete_imu_clearance_poses": 25
|
||||
},
|
||||
"source_assembly_sha256": "929e43fc28c8f63ad9bd4a1d1b593e0ef5fee37d717d09e4c1d47d5356c6f2c2",
|
||||
"mesh_export_tolerance_mm": 0.04,
|
||||
"minimum_mesh_coordinate_tolerance_mm": 0.04,
|
||||
"hardware_tested": false,
|
||||
"sliced": false
|
||||
"hardware_tested": false
|
||||
}
|
||||
|
||||
@ -1,77 +0,0 @@
|
||||
# 100×80 mm 大底板:QMI8658C 刚性安装与仿真 site
|
||||
|
||||
这版在独立目录中给现有双舵机大底板增加 IMU 安装位,保留原四个舵机固定孔与两轴几何。新增的是底板变体和小型刚性边槽座,不是实机适配验收。
|
||||
|
||||
- [含 IMU 的 STEP 装配](output/large_plate_imu_assembly.step)
|
||||
- [IMU 位置与坐标图](output/imu_placement.png)
|
||||
- [整机 CAD 投影图](output/cad_assembly.png)
|
||||
- `output/manifest.json`:分件归属、坐标、占位边界、离散干涉检查与来源摘要。
|
||||
- `output/print/large_plate.step` / `.stl`:保留原四孔、另加两个 IMU 孔的底板变体。
|
||||
- `output/print/imu_holder_TRIAL.step` / `.stl`:待实物配合检查的可拆固定座。尚未切片或发送打印。
|
||||
|
||||
## 放置位置
|
||||
|
||||
以原大底板左下角为 CAD `(0,0,0)`,`+X` 沿 100 mm 边、`+Y` 沿 80 mm 边、`+Z` 朝板上方。IMU 安装在底板左侧空出的刚性区域,不能固定在活动的 `roll_frame` 或 `pitch_arm` 上。
|
||||
|
||||
| 项目 | CAD 坐标 / 尺寸 |
|
||||
|---|---|
|
||||
| PCB 几何中心 | `(17,40,7.0)` mm |
|
||||
| PCB 占位 | X=8.5…25.5,Y=29…51,Z=6.2…7.8 mm |
|
||||
| 模块外形 | X向17 × Y向22 × 厚1.6 mm,厚度为待量尺寸 |
|
||||
| 仿真芯片 site | `(17,40,8.8)` mm,**芯片实际位置未测** |
|
||||
| 机器人根原点 | CAD `(50,40,0)` mm |
|
||||
| site 相对机器人根 | `[-0.033,0,0.0088]` m |
|
||||
| 新增两个固定孔 | CAD `(5,31)`、`(5,49)` mm;孔径2.4 mm |
|
||||
|
||||
中央空间已被舵机座占用,这个位置在其侧边且与其同一块底板刚性连接。仿真必须把加速度计和陀螺仪放到上述 site,不能把加速度计放在根原点后声称等同实机:离旋转中心的偏置会改变旋转时测得的加速度。芯片位置实测后应同步更新 site,或对约几毫米的安装偏差做训练随机化。
|
||||
|
||||
QMI8658C 小板、元件区及直排针/接插件均为明确标注的包络,不是厂商精密 CAD。22×17 mm 来自用户模块图;PCB厚度、元件高度、排针朝向与芯片中心尚待实物确认。模块安装孔距未知,本方案不利用或虚构它的孔位。
|
||||
|
||||
## 如何固定
|
||||
|
||||
新增橙色刚性座用 **2 颗 M2×8、2 片 0.5 mm M2 平垫、2 个 M2 螺母**固定。底板变体的两个螺母沉槽从底面开放,名义尖端距板底0.5 mm,避免底面螺钉先于底板触地。原来四组舵机座紧固件继续保留。
|
||||
|
||||
模块由两侧窄边槽与端部止挡约束,不依靠软泡棉。PCB槽内名义宽17.5 mm、底面Z=6.2、压边下表面Z=8.05,适配1.6 mm PCB时上方净隙0.25 mm;槽口仅占PCB边缘少量宽度。微型入口止挡和元件边距需要实测配合,不能直接把这份 STL 当作已能卡住用户小板的量产件。如果模块边缘有元件、焊点或排针冲突,应先改座,不能把压力压在芯片/电容上。
|
||||
|
||||
先将螺母从底面放入槽,固定座放板顶并用两颗M2×8拧紧;PCB对准槽滑入、检查止挡与边缘约束。装配后小板应无可见晃动,不能靠绷紧导线定位。该插入、止挡弹性及抗翻滚脱落尚未实物验证。
|
||||
|
||||
## 安装方向与部署接口
|
||||
|
||||
计划让传感器坐标满足:
|
||||
|
||||
```text
|
||||
sensor +X → body +Y
|
||||
sensor +Y → body -X
|
||||
sensor +Z → body +Z
|
||||
|
||||
R_sensor_to_body = [[0,-1,0],
|
||||
[1, 0,0],
|
||||
[0, 0,1]]
|
||||
body_vector = R_sensor_to_body @ sensor_vector
|
||||
```
|
||||
|
||||
这是**本次安装设计约定**,不是对新实机的测量结果。不能从PCB长短边或芯片文字朝向猜坐标。装入前应核对小板丝印的X/Y箭头;如果它无法同时满足上图的板边摆放和目标轴向,则保留牢固的实际摆放,重新求 `R_sensor_to_body`,不要强套矩阵。
|
||||
|
||||
板平放时应测到重力朝上,随后分别将body +X、body +Y一侧抬起,检查向量与角速度正号,确认安装旋转与零偏。旧X5装配测得的矩阵不能直接当作这次重新安装后的标定。滤波后的up向量和去偏角速度都应使用同一R转换,训练与实机接口的单位必须一致。普通舵机没有关节角反馈,上次命令仍须作为命令历史,不能改称实测关节角。
|
||||
|
||||
线束先在底板左侧做应力释放,再沿 `-Y` 方向引出,留弯曲余量并远离活动框与输出轴。小板自身的 `SDA/SCL` 用于主机,`XDA/XCL` 不代替主机接口。供电与逻辑电平按实物模块规格确认;本次没有改变此前核对的电气接线,也没有操作GPIO。
|
||||
|
||||
若X5继续放在外部作为控制器,细软信号线不能拖住底板、承重或在翻转时拉紧。X5、电源和电池没有纳入这版活动刚体;以后若把它们重新固定到底板,必须增加质量/惯量和接触几何后再训练。当前线缆拖曳和电气噪声尚未建模。
|
||||
|
||||
## 已检查与未检查
|
||||
|
||||
已完成原32个实体加IMU方案后的42实体STEP回读、IMU新增分件与静态底板/舵机座/下舵机的实体交叠检查。完整arm1与arm2分组(包括两只原装舵盘占位)在 `q1,q2 ∈ {-60,-30,0,30,60}°` 的25种组合中,均未与PCB、元件、排针/插头、刚性座及新紧固件相交。
|
||||
|
||||
这不是连续全行程证明,且±60°不是已实测安全限位。未检查实际PCB槽配合、夹持承载、止挡弹性、线束运动、电气噪声、底板刚度或实机动态。没有新打印任务。
|
||||
|
||||
复现:
|
||||
|
||||
```sh
|
||||
python -B 3Dmodel/selfrising_sg90_large_plate_imu_20261111/build_imu_mount.py
|
||||
```
|
||||
|
||||
IMU整模块质量暂按2 g(PCB+元件+排针合计),不是三个包络各2 g。固定座CAD体积约1071.69 mm³,打印质量须按材料、填充和实测修正。
|
||||
|
||||
## 仓库唯一保留版本
|
||||
|
||||
2026-11-17起仅保留本版。生成输入改为`source/assembly.step`与`source/manifest.json`(均为本版本身的冻结输入),公共函数在`support/`;其他版本不再是依赖。完整打印集合与数量以顶层`3Dmodel/README.md`和`print_manifest.json`为准。
|
||||
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
|
Before Width: | Height: | Size: 120 KiB |
Binary file not shown.
|
Before Width: | Height: | Size: 135 KiB |
File diff suppressed because it is too large
Load Diff
@ -1,939 +0,0 @@
|
||||
{
|
||||
"status": "IMU_MOUNT_LAYOUT_TRIAL_NOT_HARDWARE_APPROVED",
|
||||
"units": "mm",
|
||||
"parts": [
|
||||
{
|
||||
"name": "large_plate",
|
||||
"label": "100×80×5 底板(原四孔 + 两个 IMU 固定孔)",
|
||||
"mesh": "assembly/large_plate.stl",
|
||||
"color": "#c7a449",
|
||||
"group": "foot",
|
||||
"category": "new"
|
||||
},
|
||||
{
|
||||
"name": "servo1",
|
||||
"label": "蓝壳 SG90 下轴参考",
|
||||
"mesh": "assembly/servo1.stl",
|
||||
"color": "#357bc0",
|
||||
"group": "foot",
|
||||
"category": "purchase"
|
||||
},
|
||||
{
|
||||
"name": "servo2",
|
||||
"label": "蓝壳 SG90 上轴参考",
|
||||
"mesh": "assembly/servo2.stl",
|
||||
"color": "#357bc0",
|
||||
"group": "arm1",
|
||||
"category": "purchase"
|
||||
},
|
||||
{
|
||||
"name": "sg90_mount",
|
||||
"label": "新下轴水平固定座",
|
||||
"mesh": "assembly/sg90_mount.stl",
|
||||
"color": "#edb632",
|
||||
"group": "foot",
|
||||
"category": "new"
|
||||
},
|
||||
{
|
||||
"name": "roll_frame",
|
||||
"label": "新双侧支撑框与上舵机座",
|
||||
"mesh": "assembly/roll_frame.stl",
|
||||
"color": "#e5a329",
|
||||
"group": "arm1",
|
||||
"category": "new"
|
||||
},
|
||||
{
|
||||
"name": "pitch_arm",
|
||||
"label": "新俯仰支撑臂与起身杆",
|
||||
"mesh": "assembly/pitch_arm.stl",
|
||||
"color": "#e5a329",
|
||||
"group": "arm2",
|
||||
"category": "new"
|
||||
},
|
||||
{
|
||||
"name": "horn_strip_1",
|
||||
"label": "舵盘夹条 1",
|
||||
"mesh": "assembly/horn_strip_1.stl",
|
||||
"color": "#edb632",
|
||||
"group": "arm1",
|
||||
"category": "new"
|
||||
},
|
||||
{
|
||||
"name": "horn_strip_2",
|
||||
"label": "舵盘夹条 2",
|
||||
"mesh": "assembly/horn_strip_2.stl",
|
||||
"color": "#edb632",
|
||||
"group": "arm1",
|
||||
"category": "new"
|
||||
},
|
||||
{
|
||||
"name": "horn_strip_3",
|
||||
"label": "舵盘夹条 3",
|
||||
"mesh": "assembly/horn_strip_3.stl",
|
||||
"color": "#edb632",
|
||||
"group": "arm2",
|
||||
"category": "new"
|
||||
},
|
||||
{
|
||||
"name": "horn_strip_4",
|
||||
"label": "舵盘夹条 4",
|
||||
"mesh": "assembly/horn_strip_4.stl",
|
||||
"color": "#edb632",
|
||||
"group": "arm2",
|
||||
"category": "new"
|
||||
},
|
||||
{
|
||||
"name": "factory_horn1_ENVELOPE",
|
||||
"label": "原装双臂舵盘占位 1",
|
||||
"mesh": "assembly/factory_horn1_ENVELOPE.stl",
|
||||
"color": "#f0ece0",
|
||||
"group": "arm1",
|
||||
"category": "purchase"
|
||||
},
|
||||
{
|
||||
"name": "factory_horn2_ENVELOPE",
|
||||
"label": "原装双臂舵盘占位 2",
|
||||
"mesh": "assembly/factory_horn2_ENVELOPE.stl",
|
||||
"color": "#f0ece0",
|
||||
"group": "arm2",
|
||||
"category": "purchase"
|
||||
},
|
||||
{
|
||||
"name": "idler_bushing1",
|
||||
"label": "打印惰轴带肩衬套 1",
|
||||
"mesh": "assembly/idler_bushing1.stl",
|
||||
"color": "#edb632",
|
||||
"group": "foot",
|
||||
"category": "new"
|
||||
},
|
||||
{
|
||||
"name": "idler_bushing2",
|
||||
"label": "打印惰轴带肩衬套 2",
|
||||
"mesh": "assembly/idler_bushing2.stl",
|
||||
"color": "#edb632",
|
||||
"group": "arm1",
|
||||
"category": "new"
|
||||
},
|
||||
{
|
||||
"name": "idler_bolt1",
|
||||
"label": "外购 M2.5×8 惰轴螺钉",
|
||||
"mesh": "assembly/idler_bolt1.stl",
|
||||
"color": "#adb5be",
|
||||
"group": "foot",
|
||||
"category": "hardware"
|
||||
},
|
||||
{
|
||||
"name": "idler_bolt2",
|
||||
"label": "外购 M2.5×8 惰轴螺钉",
|
||||
"mesh": "assembly/idler_bolt2.stl",
|
||||
"color": "#adb5be",
|
||||
"group": "arm1",
|
||||
"category": "hardware"
|
||||
},
|
||||
{
|
||||
"name": "idler_washer1",
|
||||
"label": "外购 M2.5 平垫 1",
|
||||
"mesh": "assembly/idler_washer1.stl",
|
||||
"color": "#adb5be",
|
||||
"group": "foot",
|
||||
"category": "hardware"
|
||||
},
|
||||
{
|
||||
"name": "idler_washer2",
|
||||
"label": "外购 M2.5 平垫 2",
|
||||
"mesh": "assembly/idler_washer2.stl",
|
||||
"color": "#adb5be",
|
||||
"group": "arm1",
|
||||
"category": "hardware"
|
||||
},
|
||||
{
|
||||
"name": "idler_nut1",
|
||||
"label": "外购 M2.5 螺母 1",
|
||||
"mesh": "assembly/idler_nut1.stl",
|
||||
"color": "#adb5be",
|
||||
"group": "foot",
|
||||
"category": "hardware"
|
||||
},
|
||||
{
|
||||
"name": "idler_nut2",
|
||||
"label": "外购 M2.5 螺母 2",
|
||||
"mesh": "assembly/idler_nut2.stl",
|
||||
"color": "#adb5be",
|
||||
"group": "arm1",
|
||||
"category": "hardware"
|
||||
},
|
||||
{
|
||||
"name": "plate_screw_1",
|
||||
"label": "底板连接 screw 1",
|
||||
"mesh": "assembly/plate_screw_1.stl",
|
||||
"color": "#adb5be",
|
||||
"group": "foot",
|
||||
"category": "hardware"
|
||||
},
|
||||
{
|
||||
"name": "plate_washer_1",
|
||||
"label": "底板连接 washer 1",
|
||||
"mesh": "assembly/plate_washer_1.stl",
|
||||
"color": "#adb5be",
|
||||
"group": "foot",
|
||||
"category": "hardware"
|
||||
},
|
||||
{
|
||||
"name": "plate_nut_1",
|
||||
"label": "底板连接 nut 1",
|
||||
"mesh": "assembly/plate_nut_1.stl",
|
||||
"color": "#adb5be",
|
||||
"group": "foot",
|
||||
"category": "hardware"
|
||||
},
|
||||
{
|
||||
"name": "plate_screw_2",
|
||||
"label": "底板连接 screw 2",
|
||||
"mesh": "assembly/plate_screw_2.stl",
|
||||
"color": "#adb5be",
|
||||
"group": "foot",
|
||||
"category": "hardware"
|
||||
},
|
||||
{
|
||||
"name": "plate_washer_2",
|
||||
"label": "底板连接 washer 2",
|
||||
"mesh": "assembly/plate_washer_2.stl",
|
||||
"color": "#adb5be",
|
||||
"group": "foot",
|
||||
"category": "hardware"
|
||||
},
|
||||
{
|
||||
"name": "plate_nut_2",
|
||||
"label": "底板连接 nut 2",
|
||||
"mesh": "assembly/plate_nut_2.stl",
|
||||
"color": "#adb5be",
|
||||
"group": "foot",
|
||||
"category": "hardware"
|
||||
},
|
||||
{
|
||||
"name": "plate_screw_3",
|
||||
"label": "底板连接 screw 3",
|
||||
"mesh": "assembly/plate_screw_3.stl",
|
||||
"color": "#adb5be",
|
||||
"group": "foot",
|
||||
"category": "hardware"
|
||||
},
|
||||
{
|
||||
"name": "plate_washer_3",
|
||||
"label": "底板连接 washer 3",
|
||||
"mesh": "assembly/plate_washer_3.stl",
|
||||
"color": "#adb5be",
|
||||
"group": "foot",
|
||||
"category": "hardware"
|
||||
},
|
||||
{
|
||||
"name": "plate_nut_3",
|
||||
"label": "底板连接 nut 3",
|
||||
"mesh": "assembly/plate_nut_3.stl",
|
||||
"color": "#adb5be",
|
||||
"group": "foot",
|
||||
"category": "hardware"
|
||||
},
|
||||
{
|
||||
"name": "plate_screw_4",
|
||||
"label": "底板连接 screw 4",
|
||||
"mesh": "assembly/plate_screw_4.stl",
|
||||
"color": "#adb5be",
|
||||
"group": "foot",
|
||||
"category": "hardware"
|
||||
},
|
||||
{
|
||||
"name": "plate_washer_4",
|
||||
"label": "底板连接 washer 4",
|
||||
"mesh": "assembly/plate_washer_4.stl",
|
||||
"color": "#adb5be",
|
||||
"group": "foot",
|
||||
"category": "hardware"
|
||||
},
|
||||
{
|
||||
"name": "plate_nut_4",
|
||||
"label": "底板连接 nut 4",
|
||||
"mesh": "assembly/plate_nut_4.stl",
|
||||
"color": "#adb5be",
|
||||
"group": "foot",
|
||||
"category": "hardware"
|
||||
},
|
||||
{
|
||||
"name": "imu_holder_TRIAL",
|
||||
"label": "可拆刚性 IMU 边槽座(待实物适配)",
|
||||
"mesh": "assembly/imu_holder_TRIAL.stl",
|
||||
"color": "#f0782d",
|
||||
"group": "foot",
|
||||
"category": "new"
|
||||
},
|
||||
{
|
||||
"name": "imu_pcb_22x17_ENVELOPE",
|
||||
"label": "QMI8658C 22×17×1.6 PCB 占位",
|
||||
"mesh": "assembly/imu_pcb_22x17_ENVELOPE.stl",
|
||||
"color": "#813698",
|
||||
"group": "foot",
|
||||
"category": "purchase"
|
||||
},
|
||||
{
|
||||
"name": "imu_components_ENVELOPE",
|
||||
"label": "模块元件空间占位,非芯片精密模型",
|
||||
"mesh": "assembly/imu_components_ENVELOPE.stl",
|
||||
"color": "#282d38",
|
||||
"group": "foot",
|
||||
"category": "purchase"
|
||||
},
|
||||
{
|
||||
"name": "imu_header_8pin_ENVELOPE",
|
||||
"label": "8针直排针/插头空间占位",
|
||||
"mesh": "assembly/imu_header_8pin_ENVELOPE.stl",
|
||||
"color": "#d4c390",
|
||||
"group": "foot",
|
||||
"category": "purchase"
|
||||
},
|
||||
{
|
||||
"name": "imu_screw_1",
|
||||
"label": "外购 M2×8 IMU 座螺钉",
|
||||
"mesh": "assembly/imu_screw_1.stl",
|
||||
"color": "#adb5be",
|
||||
"group": "foot",
|
||||
"category": "hardware"
|
||||
},
|
||||
{
|
||||
"name": "imu_washer_1",
|
||||
"label": "外购 M2 平垫 0.5mm",
|
||||
"mesh": "assembly/imu_washer_1.stl",
|
||||
"color": "#adb5be",
|
||||
"group": "foot",
|
||||
"category": "hardware"
|
||||
},
|
||||
{
|
||||
"name": "imu_nut_1",
|
||||
"label": "外购 M2 螺母",
|
||||
"mesh": "assembly/imu_nut_1.stl",
|
||||
"color": "#adb5be",
|
||||
"group": "foot",
|
||||
"category": "hardware"
|
||||
},
|
||||
{
|
||||
"name": "imu_screw_2",
|
||||
"label": "外购 M2×8 IMU 座螺钉",
|
||||
"mesh": "assembly/imu_screw_2.stl",
|
||||
"color": "#adb5be",
|
||||
"group": "foot",
|
||||
"category": "hardware"
|
||||
},
|
||||
{
|
||||
"name": "imu_washer_2",
|
||||
"label": "外购 M2 平垫 0.5mm",
|
||||
"mesh": "assembly/imu_washer_2.stl",
|
||||
"color": "#adb5be",
|
||||
"group": "foot",
|
||||
"category": "hardware"
|
||||
},
|
||||
{
|
||||
"name": "imu_nut_2",
|
||||
"label": "外购 M2 螺母",
|
||||
"mesh": "assembly/imu_nut_2.stl",
|
||||
"color": "#adb5be",
|
||||
"group": "foot",
|
||||
"category": "hardware"
|
||||
}
|
||||
],
|
||||
"source_step_sha256": "9394c5e2144121eeb9b5d476b77177f6f54fe4ee74c1d8f29afd2db31e045fce",
|
||||
"source_manifest_sha256": "93abdf9d44a7f9166de39bc617ae820bf7494b85fa76fa2aa7b92d4d41a9f889",
|
||||
"source_code_sha256": "125dbc9332858937778eb344267958f0a2cfceabcc0ba0f1c31bfeaa604d96b0",
|
||||
"original_servo_holes_preserved": true,
|
||||
"imu_mount_holes_xy_mm": [
|
||||
[
|
||||
5.0,
|
||||
31.0
|
||||
],
|
||||
[
|
||||
5.0,
|
||||
49.0
|
||||
]
|
||||
],
|
||||
"connection": {
|
||||
"screws": "M2x8",
|
||||
"quantity": 2,
|
||||
"washers": "M2 0.5 mm",
|
||||
"nuts": "M2",
|
||||
"screw_tip_above_plate_bottom_mm": 0.5
|
||||
},
|
||||
"pcb_centre_cad_mm": [
|
||||
17.0,
|
||||
40.0,
|
||||
7.0
|
||||
],
|
||||
"pcb_envelope_mm": [
|
||||
17,
|
||||
22,
|
||||
1.6
|
||||
],
|
||||
"module_total_mass_kg_assumed": 0.002,
|
||||
"imu_site_cad_mm": [
|
||||
17.0,
|
||||
40.0,
|
||||
8.8
|
||||
],
|
||||
"imu_site_is_measured_chip_centre": false,
|
||||
"robot_root_cad_mm": [
|
||||
50,
|
||||
40,
|
||||
0
|
||||
],
|
||||
"imu_site_relative_to_root_m": [
|
||||
-0.033,
|
||||
0,
|
||||
0.0088
|
||||
],
|
||||
"body_axes": {
|
||||
"x": "CAD +X, 100mm edge",
|
||||
"y": "CAD +Y, 80mm edge",
|
||||
"z": "away from plate top"
|
||||
},
|
||||
"sensor_to_body_design_R": [
|
||||
[
|
||||
0,
|
||||
-1,
|
||||
0
|
||||
],
|
||||
[
|
||||
1,
|
||||
0,
|
||||
0
|
||||
],
|
||||
[
|
||||
0,
|
||||
0,
|
||||
1
|
||||
]
|
||||
],
|
||||
"sensor_to_body_is_measured": false,
|
||||
"desired_sensor_axes": {
|
||||
"sensor_x": "body +Y",
|
||||
"sensor_y": "body -X",
|
||||
"sensor_z": "body +Z"
|
||||
},
|
||||
"cable_exit": "toward CAD -Y along left-side edge after local strain relief; keep away from moving frame",
|
||||
"zero_checks": [
|
||||
{
|
||||
"a": "imu_holder_TRIAL",
|
||||
"b": "large_plate",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_holder_TRIAL",
|
||||
"b": "sg90_mount",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_holder_TRIAL",
|
||||
"b": "servo1",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_holder_TRIAL",
|
||||
"b": "imu_pcb_22x17_ENVELOPE",
|
||||
"overlap_mm3": 0
|
||||
},
|
||||
{
|
||||
"a": "imu_holder_TRIAL",
|
||||
"b": "imu_components_ENVELOPE",
|
||||
"overlap_mm3": 0
|
||||
},
|
||||
{
|
||||
"a": "imu_holder_TRIAL",
|
||||
"b": "imu_header_8pin_ENVELOPE",
|
||||
"overlap_mm3": 0
|
||||
},
|
||||
{
|
||||
"a": "imu_holder_TRIAL",
|
||||
"b": "imu_screw_1",
|
||||
"overlap_mm3": 0
|
||||
},
|
||||
{
|
||||
"a": "imu_holder_TRIAL",
|
||||
"b": "imu_washer_1",
|
||||
"overlap_mm3": 0
|
||||
},
|
||||
{
|
||||
"a": "imu_holder_TRIAL",
|
||||
"b": "imu_nut_1",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_holder_TRIAL",
|
||||
"b": "imu_screw_2",
|
||||
"overlap_mm3": 0
|
||||
},
|
||||
{
|
||||
"a": "imu_holder_TRIAL",
|
||||
"b": "imu_washer_2",
|
||||
"overlap_mm3": 0
|
||||
},
|
||||
{
|
||||
"a": "imu_holder_TRIAL",
|
||||
"b": "imu_nut_2",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_pcb_22x17_ENVELOPE",
|
||||
"b": "large_plate",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_pcb_22x17_ENVELOPE",
|
||||
"b": "sg90_mount",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_pcb_22x17_ENVELOPE",
|
||||
"b": "servo1",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_pcb_22x17_ENVELOPE",
|
||||
"b": "imu_components_ENVELOPE",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_pcb_22x17_ENVELOPE",
|
||||
"b": "imu_header_8pin_ENVELOPE",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_pcb_22x17_ENVELOPE",
|
||||
"b": "imu_screw_1",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_pcb_22x17_ENVELOPE",
|
||||
"b": "imu_washer_1",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_pcb_22x17_ENVELOPE",
|
||||
"b": "imu_nut_1",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_pcb_22x17_ENVELOPE",
|
||||
"b": "imu_screw_2",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_pcb_22x17_ENVELOPE",
|
||||
"b": "imu_washer_2",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_pcb_22x17_ENVELOPE",
|
||||
"b": "imu_nut_2",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_components_ENVELOPE",
|
||||
"b": "large_plate",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_components_ENVELOPE",
|
||||
"b": "sg90_mount",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_components_ENVELOPE",
|
||||
"b": "servo1",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_components_ENVELOPE",
|
||||
"b": "imu_header_8pin_ENVELOPE",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_components_ENVELOPE",
|
||||
"b": "imu_screw_1",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_components_ENVELOPE",
|
||||
"b": "imu_washer_1",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_components_ENVELOPE",
|
||||
"b": "imu_nut_1",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_components_ENVELOPE",
|
||||
"b": "imu_screw_2",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_components_ENVELOPE",
|
||||
"b": "imu_washer_2",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_components_ENVELOPE",
|
||||
"b": "imu_nut_2",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_header_8pin_ENVELOPE",
|
||||
"b": "large_plate",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_header_8pin_ENVELOPE",
|
||||
"b": "sg90_mount",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_header_8pin_ENVELOPE",
|
||||
"b": "servo1",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_header_8pin_ENVELOPE",
|
||||
"b": "imu_screw_1",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_header_8pin_ENVELOPE",
|
||||
"b": "imu_washer_1",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_header_8pin_ENVELOPE",
|
||||
"b": "imu_nut_1",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_header_8pin_ENVELOPE",
|
||||
"b": "imu_screw_2",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_header_8pin_ENVELOPE",
|
||||
"b": "imu_washer_2",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_header_8pin_ENVELOPE",
|
||||
"b": "imu_nut_2",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_screw_1",
|
||||
"b": "large_plate",
|
||||
"overlap_mm3": 0
|
||||
},
|
||||
{
|
||||
"a": "imu_screw_1",
|
||||
"b": "sg90_mount",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_screw_1",
|
||||
"b": "servo1",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_screw_1",
|
||||
"b": "imu_washer_1",
|
||||
"overlap_mm3": 0
|
||||
},
|
||||
{
|
||||
"a": "imu_screw_1",
|
||||
"b": "imu_nut_1",
|
||||
"overlap_mm3": 0
|
||||
},
|
||||
{
|
||||
"a": "imu_screw_1",
|
||||
"b": "imu_screw_2",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_screw_1",
|
||||
"b": "imu_washer_2",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_screw_1",
|
||||
"b": "imu_nut_2",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_washer_1",
|
||||
"b": "large_plate",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_washer_1",
|
||||
"b": "sg90_mount",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_washer_1",
|
||||
"b": "servo1",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_washer_1",
|
||||
"b": "imu_nut_1",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_washer_1",
|
||||
"b": "imu_screw_2",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_washer_1",
|
||||
"b": "imu_washer_2",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_washer_1",
|
||||
"b": "imu_nut_2",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_nut_1",
|
||||
"b": "large_plate",
|
||||
"overlap_mm3": 0
|
||||
},
|
||||
{
|
||||
"a": "imu_nut_1",
|
||||
"b": "sg90_mount",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_nut_1",
|
||||
"b": "servo1",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_nut_1",
|
||||
"b": "imu_screw_2",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_nut_1",
|
||||
"b": "imu_washer_2",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_nut_1",
|
||||
"b": "imu_nut_2",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_screw_2",
|
||||
"b": "large_plate",
|
||||
"overlap_mm3": 0
|
||||
},
|
||||
{
|
||||
"a": "imu_screw_2",
|
||||
"b": "sg90_mount",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_screw_2",
|
||||
"b": "servo1",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_screw_2",
|
||||
"b": "imu_washer_2",
|
||||
"overlap_mm3": 0
|
||||
},
|
||||
{
|
||||
"a": "imu_screw_2",
|
||||
"b": "imu_nut_2",
|
||||
"overlap_mm3": 0
|
||||
},
|
||||
{
|
||||
"a": "imu_washer_2",
|
||||
"b": "large_plate",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_washer_2",
|
||||
"b": "sg90_mount",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_washer_2",
|
||||
"b": "servo1",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_washer_2",
|
||||
"b": "imu_nut_2",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_nut_2",
|
||||
"b": "large_plate",
|
||||
"overlap_mm3": 0
|
||||
},
|
||||
{
|
||||
"a": "imu_nut_2",
|
||||
"b": "sg90_mount",
|
||||
"overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"a": "imu_nut_2",
|
||||
"b": "servo1",
|
||||
"overlap_mm3": 0.0
|
||||
}
|
||||
],
|
||||
"sampled_motion": [
|
||||
{
|
||||
"q1_deg": -60,
|
||||
"q2_deg": -60,
|
||||
"imu_overlap_mm3": 0
|
||||
},
|
||||
{
|
||||
"q1_deg": -60,
|
||||
"q2_deg": -30,
|
||||
"imu_overlap_mm3": 0
|
||||
},
|
||||
{
|
||||
"q1_deg": -60,
|
||||
"q2_deg": 0,
|
||||
"imu_overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"q1_deg": -60,
|
||||
"q2_deg": 30,
|
||||
"imu_overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"q1_deg": -60,
|
||||
"q2_deg": 60,
|
||||
"imu_overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"q1_deg": -30,
|
||||
"q2_deg": -60,
|
||||
"imu_overlap_mm3": 0
|
||||
},
|
||||
{
|
||||
"q1_deg": -30,
|
||||
"q2_deg": -30,
|
||||
"imu_overlap_mm3": 0
|
||||
},
|
||||
{
|
||||
"q1_deg": -30,
|
||||
"q2_deg": 0,
|
||||
"imu_overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"q1_deg": -30,
|
||||
"q2_deg": 30,
|
||||
"imu_overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"q1_deg": -30,
|
||||
"q2_deg": 60,
|
||||
"imu_overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"q1_deg": 0,
|
||||
"q2_deg": -60,
|
||||
"imu_overlap_mm3": 0
|
||||
},
|
||||
{
|
||||
"q1_deg": 0,
|
||||
"q2_deg": -30,
|
||||
"imu_overlap_mm3": 0
|
||||
},
|
||||
{
|
||||
"q1_deg": 0,
|
||||
"q2_deg": 0,
|
||||
"imu_overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"q1_deg": 0,
|
||||
"q2_deg": 30,
|
||||
"imu_overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"q1_deg": 0,
|
||||
"q2_deg": 60,
|
||||
"imu_overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"q1_deg": 30,
|
||||
"q2_deg": -60,
|
||||
"imu_overlap_mm3": 0
|
||||
},
|
||||
{
|
||||
"q1_deg": 30,
|
||||
"q2_deg": -30,
|
||||
"imu_overlap_mm3": 0
|
||||
},
|
||||
{
|
||||
"q1_deg": 30,
|
||||
"q2_deg": 0,
|
||||
"imu_overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"q1_deg": 30,
|
||||
"q2_deg": 30,
|
||||
"imu_overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"q1_deg": 30,
|
||||
"q2_deg": 60,
|
||||
"imu_overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"q1_deg": 60,
|
||||
"q2_deg": -60,
|
||||
"imu_overlap_mm3": 0
|
||||
},
|
||||
{
|
||||
"q1_deg": 60,
|
||||
"q2_deg": -30,
|
||||
"imu_overlap_mm3": 0
|
||||
},
|
||||
{
|
||||
"q1_deg": 60,
|
||||
"q2_deg": 0,
|
||||
"imu_overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"q1_deg": 60,
|
||||
"q2_deg": 30,
|
||||
"imu_overlap_mm3": 0.0
|
||||
},
|
||||
{
|
||||
"q1_deg": 60,
|
||||
"q2_deg": 60,
|
||||
"imu_overlap_mm3": 0.0
|
||||
}
|
||||
],
|
||||
"sampled_motion_clear": true,
|
||||
"continuous_motion_checked": false,
|
||||
"physical_fit_checked": false,
|
||||
"load_checked": false,
|
||||
"module_mounting_hole_geometry_unknown": true,
|
||||
"chip_location_unknown": true,
|
||||
"limitations": [
|
||||
"PCB, component and connector envelopes are declared placeholders, not module factory CAD",
|
||||
"Sliding edge grooves/entry detents require measured thickness and component-edge clearance",
|
||||
"Existing module arrows and new mounting rotation must be verified before using design R",
|
||||
"Wire bending, pull loads, flex and dynamic vibration are not verified",
|
||||
"Only 25 discrete poses, not a continuous swept-volume proof"
|
||||
],
|
||||
"step_roundtrip_solids": 42,
|
||||
"printing_requested": false,
|
||||
"sent_to_printer": false
|
||||
}
|
||||
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
File diff suppressed because it is too large
Load Diff
Binary file not shown.
File diff suppressed because it is too large
Load Diff
Binary file not shown.
Binary file not shown.
Binary file not shown.
@ -1,40 +0,0 @@
|
||||
[
|
||||
{
|
||||
"part": "large_plate",
|
||||
"watertight": true,
|
||||
"winding_consistent": true,
|
||||
"volume_mm3": 39636.993045700474,
|
||||
"bounds_mm": [
|
||||
[
|
||||
-8.881784197001252e-16,
|
||||
-8.881784197001252e-16,
|
||||
0.0
|
||||
],
|
||||
[
|
||||
100.0,
|
||||
80.0,
|
||||
5.0
|
||||
]
|
||||
],
|
||||
"sha256": "eb4060ce8862037d8f80628e7b1a086ec4109011a89dd3717ec88da131c2c09f"
|
||||
},
|
||||
{
|
||||
"part": "imu_holder_TRIAL",
|
||||
"watertight": true,
|
||||
"winding_consistent": true,
|
||||
"volume_mm3": 1071.7040093118815,
|
||||
"bounds_mm": [
|
||||
[
|
||||
2.0,
|
||||
27.75,
|
||||
5.0
|
||||
],
|
||||
[
|
||||
26.399999618530273,
|
||||
52.25,
|
||||
8.649999618530273
|
||||
]
|
||||
],
|
||||
"sha256": "c5c90d71b74558f58ace055b967e3c172d5be3afba7256b78d21de3a80e62c45"
|
||||
}
|
||||
]
|
||||
File diff suppressed because it is too large
Load Diff
29
3Dmodel/v4_taller_rounded_imu/MODULE_DIMENSIONS.json
Normal file
29
3Dmodel/v4_taller_rounded_imu/MODULE_DIMENSIONS.json
Normal file
@ -0,0 +1,29 @@
|
||||
{
|
||||
"module": "QMI8658C 8-pin breakout; seller-specific board, actual user board not identified",
|
||||
"nominal_pcb_mm": [
|
||||
21,
|
||||
16.4
|
||||
],
|
||||
"board_thickness_mm_assumed": 1.6,
|
||||
"header_pitch_mm": 2.54,
|
||||
"source_url": "https://plexishop.it/posizione-giroscopi-bussole/10063-modulo-qmi8658c-sensore-accelerometro-e-giroscopio-a-6-assi.html",
|
||||
"source_type": "seller listing for its own module; not QST PCB mechanical specification",
|
||||
"retrieved_date": "2026-11-18",
|
||||
"pcb_mounting_hole_pitch_mm": null,
|
||||
"plate_holder_holes_mm": [
|
||||
[
|
||||
5,
|
||||
31
|
||||
],
|
||||
[
|
||||
5,
|
||||
49
|
||||
]
|
||||
],
|
||||
"plate_hole_diameter_mm": 2.4,
|
||||
"holder_hole_pitch_mm": 18,
|
||||
"holder_inner_width_mm": 16.8,
|
||||
"holder_length_clearance_mm": 0.4,
|
||||
"actual_board_measured": false,
|
||||
"pcb_dimensions_not_universal": true
|
||||
}
|
||||
46
3Dmodel/v4_taller_rounded_imu/README.md
Normal file
46
3Dmodel/v4_taller_rounded_imu/README.md
Normal file
@ -0,0 +1,46 @@
|
||||
# 加高圆角版 v4 + QMI8658C 底板固定座
|
||||
|
||||
2026-11-18。对应用户提供的“下层框加高 8 mm 并圆角”装配图。在该版大底板增加两个 M2 安装孔和底面螺母槽,配可拆边槽固定座,IMU 与底板刚性连接。
|
||||
|
||||
## 尺寸依据
|
||||
|
||||
[Plexishop 的 QMI8658C 八针模块(09A233)](https://plexishop.it/posizione-giroscopi-bussole/10063-modulo-qmi8658c-sensore-accelerometro-e-giroscopio-a-6-assi.html) 标注模块 **21 × 16.4 mm**、排针间距 **2.54 mm**。这是该商家所售板型的尺寸,不能认定所有 QMI8658C 模块都相同;没有查到该板的安装孔距。
|
||||
|
||||
本设计使用 21 × 16.4 mm PCB 外形,厚度暂按 1.6 mm;边槽内宽 16.8 mm,宽度每侧留 0.2 mm。元件、排针高度与芯片中心使用占位尺寸,未取得模块厂家机械图。尺寸、来源和假设保存在 `MODULE_DIMENSIONS.json`。
|
||||
|
||||
## 底板孔位(单位 mm)
|
||||
|
||||
底板 100 × 80 × 5,CAD 左下角为 (0,0),Z=0 为底面。
|
||||
|
||||
| 项目 | 尺寸 |
|
||||
|---|---|
|
||||
| 新增通孔 | 2 × Ø2.4,用于 M2 螺钉 |
|
||||
| 孔中心 | (5,31)、(5,49) |
|
||||
| 中心距 | 18 |
|
||||
| 底面螺母槽 | 六角对边 4.3,深 2.3 |
|
||||
| 紧固件 | 2 × M2×8,2 × M2 平垫(0.5厚),2 × M2 螺母 |
|
||||
| PCB 中心 | (17,40,7.0) |
|
||||
|
||||
18 mm 是**底板与固定座连接孔距**,不是 PCB 原有安装孔距。PCB 滑入边槽,原有四个底板孔保留。未更改舵机座、加高活动框和上臂。
|
||||
|
||||
## 文件和打印
|
||||
|
||||
- `output/cad_assembly.png`:完整装配预览。
|
||||
- `output/imu_placement.png`:孔位及安装位置。
|
||||
- `output/large_plate_imu_assembly.step`:完整装配(含模块占位和外购紧固件)。
|
||||
- `output/print/large_plate.stl`、`imu_holder_TRIAL.stl`:本次需要新打印的两个零件;对应 STEP 同目录。
|
||||
- `output/print/`:全套五个塑料零件,另外三个沿用原 v4。
|
||||
- `source/`:未改动的 v4 原装配及清单,便于回溯。
|
||||
|
||||
## 已完成检查及边界
|
||||
|
||||
生成器核对新增零件静态相交、STEP 导入导出有效性,以及下轴 -90° 至 +90°、上轴 -60° 至 +60° 的 35 个离散组合姿态与新增 IMU 结构的碰撞。`verify_design.py` 另查源装配其他零件几何未变、底板尺寸与新增孔/螺母槽、五个打印网格闭合且有正体积。结果见 `output/verification.json`。
|
||||
|
||||
未检查连续扫掠、线束弯折、强度或实物装配。槽口与卡点需试装;模块板型、厚度及边缘元件净空未实测,不能作为已适配证明。PCB 轴向及占位芯片位置不能直接当成实机标定数据。未发送打印。
|
||||
|
||||
复现环境:Python 3.12、build123d 0.13.0、trimesh 5.2.0、Pillow 13.0.0、numpy 2.5.5。
|
||||
|
||||
```sh
|
||||
python -B build_imu_mount.py
|
||||
python -B verify_design.py
|
||||
```
|
||||
@ -17,22 +17,20 @@ PCB_CENTRE=(17.,40.,7.)
|
||||
SITE=(17.,40.,8.8)
|
||||
HOLES=((5.,31.),(5.,49.))
|
||||
R=((0,-1,0),(1,0,0),(0,0,1))
|
||||
PRINT_NAMES=('large_plate','sg90_mount','roll_frame','pitch_arm',
|
||||
'horn_strip_1','horn_strip_2','horn_strip_3','horn_strip_4',
|
||||
'idler_bushing1','idler_bushing2','imu_holder_TRIAL')
|
||||
PRINT_NAMES=('large_plate','sg90_mount','roll_frame','pitch_arm','imu_holder_TRIAL')
|
||||
|
||||
|
||||
def holder():
|
||||
b=cad.b
|
||||
part=b(7.6,26.4,27.75,52.25,5,6.2)
|
||||
part+=b(2,8.25,27.75,52.25,5,8)
|
||||
for x0,x1 in ((7.6,8.25),(25.75,26.4)):
|
||||
part+=b(x0,x1,28.5,52.25,6.2,8.65)
|
||||
for x0,x1 in ((8.25,8.85),(25.15,25.75)):
|
||||
part=b(7.6,26.4,28.75,51.25,5,6.2)
|
||||
part+=b(2,8.6,28.75,51.25,5,8)
|
||||
for x0,x1 in ((7.6,8.6),(25.4,26.4)):
|
||||
part+=b(x0,x1,29.25,51.25,6.2,8.65)
|
||||
for x0,x1 in ((8.6,9.2),(24.8,25.4)):
|
||||
part+=b(x0,x1,30,50.5,8.05,8.65)
|
||||
part+=b(7.6,26.4,51.25,52.25,6.2,8.65)
|
||||
part+=b(7.6,26.4,50.75,51.25,6.2,8.65)
|
||||
# shortcut: tiny PETG entry detents require a real PCB thickness/edge-fit trial.
|
||||
for x in (8.25,24.5):part+=b(x,x+.9,28.35,28.75,6.2,6.7)
|
||||
for x in (8.6,24.5):part+=b(x,x+.9,29.05,29.45,6.2,6.7)
|
||||
for x,y in HOLES:part-=cad.cyl(x,y,4.5,8.5,1.2)
|
||||
assert part.is_valid and len(part.solids())==1
|
||||
return part
|
||||
@ -57,7 +55,7 @@ def main():
|
||||
shape.label=name;shapes[name]=shape
|
||||
parts.append(dict(name=name,label=label,mesh=f'assembly/{name}.stl',color=color,group='foot',category=category))
|
||||
add('imu_holder_TRIAL',holder(),'可拆刚性 IMU 边槽座(待实物适配)','#f0782d')
|
||||
add('imu_pcb_22x17_ENVELOPE',cad.b(8.5,25.5,29,51,6.2,7.8),'QMI8658C 22×17×1.6 PCB 占位','#813698','purchase')
|
||||
add('imu_pcb_21x16p4_ENVELOPE',cad.b(8.8,25.2,29.5,50.5,6.2,7.8),'QMI8658C 21×16.4 PCB参考,厚1.6待实测','#813698','purchase')
|
||||
add('imu_components_ENVELOPE',cad.b(12.5,23.7,30.5,49.5,7.8,10.8),'模块元件空间占位,非芯片精密模型','#282d38','purchase')
|
||||
add('imu_header_8pin_ENVELOPE',cad.b(9.5,12.1,30.3,49.7,7.8,16.8),'8针直排针/插头空间占位','#d4c390','purchase')
|
||||
for i,(x,y) in enumerate(HOLES,1):
|
||||
@ -71,19 +69,19 @@ def main():
|
||||
for target in ['large_plate','sg90_mount','servo1']+imu_names[i+1:]:
|
||||
overlap=cad.overlap(shapes[name],shapes[target])
|
||||
checks.append(dict(a=name,b=target,overlap_mm3=overlap));assert overlap<1e-5,checks[-1]
|
||||
a1=np.array([33.,44.,25.3]);a2=np.array([48.5,29.,73.1])
|
||||
a1=np.array([33.,44.,33.3]);a2=np.array([48.5,29.,89.1])
|
||||
first_names=[p['name'] for p in parts if p['group']=='arm1']
|
||||
second_names=[p['name'] for p in parts if p['group']=='arm2']
|
||||
immovable=bd.Compound(children=[shapes[n] for n in imu_names])
|
||||
sweep=[]
|
||||
for q1,q2 in itertools.product((-60,-30,0,30,60),repeat=2):
|
||||
for q1,q2 in itertools.product((-90,-60,-30,0,30,60,90),(-60,-30,0,30,60)):
|
||||
first=bd.Compound(children=[shapes[n] for n in first_names])
|
||||
second=bd.Compound(children=[shapes[n] for n in second_names]).rotate(bd.Axis(a2,(0,1,0)),q2)
|
||||
moving=bd.Compound(children=[first,second]).rotate(bd.Axis(a1,(1,0,0)),q1)
|
||||
overlap=cad.overlap(moving,immovable)
|
||||
sweep.append(dict(q1_deg=q1,q2_deg=q2,imu_overlap_mm3=overlap))
|
||||
assert overlap<1e-5,sweep[-1]
|
||||
print('25 full grouped poses clear of IMU/module/header/holder',flush=True)
|
||||
print('35 full grouped poses clear of IMU/module/header/holder',flush=True)
|
||||
for p in parts:
|
||||
shape=shapes[p['name']];shape.label=p['name'];shape.color=bd.Color(p['color'])
|
||||
bd.export_stl(shape,str(OUT/p['mesh']),tolerance=.06,angular_tolerance=.15)
|
||||
@ -104,7 +102,7 @@ def main():
|
||||
original_servo_holes_preserved=True,imu_mount_holes_xy_mm=HOLES,
|
||||
connection=dict(screws='M2x8',quantity=2,washers='M2 0.5 mm',nuts='M2',
|
||||
screw_tip_above_plate_bottom_mm=.5),
|
||||
pcb_centre_cad_mm=PCB_CENTRE,pcb_envelope_mm=[17,22,1.6],module_total_mass_kg_assumed=.002,
|
||||
pcb_centre_cad_mm=PCB_CENTRE,pcb_envelope_mm=[16.4,21,1.6],module_total_mass_kg_assumed=.002,
|
||||
imu_site_cad_mm=SITE,imu_site_is_measured_chip_centre=False,
|
||||
robot_root_cad_mm=[50,40,0],imu_site_relative_to_root_m=[-.033,0,.0088],
|
||||
body_axes=dict(x='CAD +X, 100mm edge',y='CAD +Y, 80mm edge',z='away from plate top'),
|
||||
@ -118,7 +116,7 @@ def main():
|
||||
'Sliding edge grooves/entry detents require measured thickness and component-edge clearance',
|
||||
'Existing module arrows and new mounting rotation must be verified before using design R',
|
||||
'Wire bending, pull loads, flex and dynamic vibration are not verified',
|
||||
'Only 25 discrete poses, not a continuous swept-volume proof'],
|
||||
'Only 35 discrete poses, not a continuous swept-volume proof'],
|
||||
step_roundtrip_solids=len(roundtrip.solids()),printing_requested=False,sent_to_printer=False)
|
||||
(OUT/'manifest.json').write_text(json.dumps(report,ensure_ascii=False,indent=2)+'\n')
|
||||
render(report)
|
||||
@ -129,8 +127,8 @@ def main():
|
||||
def render(report):
|
||||
cad.render.OUT=OUT;meshes=cad.render.load_parts(report)
|
||||
page=Image.new('RGB',(1800,1240),'#f0f5f8');draw=ImageDraw.Draw(page)
|
||||
cad.render.label(draw,(35,20),'100×80 mm 双舵机大底板|IMU 刚性安装方案',36)
|
||||
cad.render.label(draw,(35,76),'紫色:22×17 mm 模块占位;橙色:可拆边槽座;原四个舵机孔保留,新增两个 M2 固定孔。',23)
|
||||
cad.render.label(draw,(35,20),'加高圆角版 + QMI8658C|底板新增IMU固定孔',36)
|
||||
cad.render.label(draw,(35,76),'紫色:21×16.4 mm模块参考;橙色:带余量边槽座;新增2ר2.4孔,中心距18 mm。',23)
|
||||
for x,eye in ((25,(1.5,-2,1.4)),(920,(-1.2,-1.7,1.3))):
|
||||
im,_=cad.render.render([(p,p['triangles']) for p in meshes],(850,980),eye=eye,margin=40)
|
||||
page.paste(im,(x,135))
|
||||
@ -146,8 +144,8 @@ def render(report):
|
||||
x0,y0,s=960,210,6
|
||||
draw.rounded_rectangle((x0,y0,x0+100*s,y0+80*s),radius=4*s,fill='#e4bf50',outline='#84641f',width=3)
|
||||
def point(x,y):return x0+x*s,y0+(80-y)*s
|
||||
draw.rectangle((*point(2,52.25),*point(26.4,27.75)),fill='#ed8745',outline='#99521b',width=2)
|
||||
draw.rectangle((*point(8.5,51),*point(25.5,29)),fill='#813698',outline='#51206b',width=2)
|
||||
draw.rectangle((*point(2,51.25),*point(26.4,28.75)),fill='#ed8745',outline='#99521b',width=2)
|
||||
draw.rectangle((*point(8.8,50.5),*point(25.2,29.5)),fill='#813698',outline='#51206b',width=2)
|
||||
draw.rectangle((*point(9.5,49.7),*point(12.1,30.3)),fill='#d4c390')
|
||||
for x,y in report['imu_mount_holes_xy_mm']:
|
||||
xx,yy=point(x,y);draw.ellipse((xx-6,yy-6,xx+6,yy+6),fill='white',outline='#555555',width=2)
|
||||
@ -164,7 +162,7 @@ def render(report):
|
||||
cad.render.label(draw,(960,815),'新孔:CAD (5,31)、(5,49);M2×8',23)
|
||||
cad.render.label(draw,(35,955),'设计方向:sensor +X → body +Y;sensor +Y → body -X;sensor +Z → body +Z。',24)
|
||||
cad.render.label(draw,(35,1000),'此 R 是待落实的安装约定,不是新实机标定结果;不得只按 PCB 长短边猜传感器轴向。',24)
|
||||
cad.render.label(draw,(35,1045),'25 组 ±60° 离散检查无 IMU 干涉;未验证连续运动、线束、打印适配或负载。未发送打印。',23)
|
||||
cad.render.label(draw,(35,1045),'35组姿态:下轴±90°、上轴±60°;不等于连续行程或实物适配。未发送打印。',23)
|
||||
page.save(OUT/'imu_placement.png')
|
||||
|
||||
|
||||
Binary file not shown.
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/horn1_screw_-1.stl
Normal file
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/horn1_screw_-1.stl
Normal file
Binary file not shown.
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/horn1_screw_1.stl
Normal file
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/horn1_screw_1.stl
Normal file
Binary file not shown.
Binary file not shown.
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/horn2_screw_-1.stl
Normal file
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/horn2_screw_-1.stl
Normal file
Binary file not shown.
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/horn2_screw_1.stl
Normal file
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/horn2_screw_1.stl
Normal file
Binary file not shown.
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/idler_bolt1.stl
Normal file
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/idler_bolt1.stl
Normal file
Binary file not shown.
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/idler_bolt2.stl
Normal file
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/idler_bolt2.stl
Normal file
Binary file not shown.
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/idler_nut1.stl
Normal file
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/idler_nut1.stl
Normal file
Binary file not shown.
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/idler_nut2.stl
Normal file
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/idler_nut2.stl
Normal file
Binary file not shown.
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/idler_washer1.stl
Normal file
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/idler_washer1.stl
Normal file
Binary file not shown.
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/idler_washer2.stl
Normal file
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/idler_washer2.stl
Normal file
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/pitch_arm.stl
Normal file
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/pitch_arm.stl
Normal file
Binary file not shown.
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/plate_screw_1.stl
Normal file
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/plate_screw_1.stl
Normal file
Binary file not shown.
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/plate_screw_4.stl
Normal file
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/plate_screw_4.stl
Normal file
Binary file not shown.
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/plate_washer_1.stl
Normal file
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/plate_washer_1.stl
Normal file
Binary file not shown.
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/plate_washer_4.stl
Normal file
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/plate_washer_4.stl
Normal file
Binary file not shown.
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/roll_frame.stl
Normal file
BIN
3Dmodel/v4_taller_rounded_imu/output/assembly/roll_frame.stl
Normal file
Binary file not shown.
Some files were not shown because too many files have changed in this diff Show More
Loading…
x
Reference in New Issue
Block a user